View the features of Clamping Control Injection Other

(std) Closed-loop control of speed and position for mould opening and closing
(std) Closed-loop control of ejection speed and position
(std) Programmable control of mould opening (2 to 5 steps)
(std) Programmable control of mould closing (3 to 5 steps)
(std) Mould exchanging mode (low pressure, low speed)
Automatic clamping force adjustment system
(std) Automatic clamping force setup system
(std) Low pressure mould protection system
(std) Mould protection in mold opening and ejection
(std) Movable die plate supported by double rollers
(std) Double safety system (electrical and mechanical)
(std) Emergency stop pushbutton (for operation and non-operation sides)
Air ejector (single or dual lines)
3-way valve for air ejector (single or dual lines)
Air-driven core system (single)
Hydraulic core system (single or dual; independent hydraulic unit)
Ejector centre pull back specification
Ejector pull back control
(std) Programmable control of ejector forwarding (1 to 3 steps)
(std) 2 step ejector
(std) Ejecting during mould opening (by position setting)
Mould ejector plate return detector (metal contacts)
Mould temperature display (2 lines, with magnet sensor)
Mould temperature control (2 lines, with magnet sensor)
Locating ring diameter 100/120 mm
T-slotted die plate (contact us)
Heat insulating board (General or High precision)
Mould height extension 60 mm
Reversible chute



(std) = standard

(std) PLCS-12 microprocessor-aided control (TFT colour LCD with full touch panel)
(std) Digital setting of all the parameters
(std) Internal memory of 400 mould setups
(std) UBS interface (1 port) for memory or printer
(std) Graphic display of injection, metering and meter waves (with memory function)
(std) Monitor graphic indication
(std) Statistical processing of monitored data
(std) Manual Unmanned mode switching function
(std) Hour meter (indication of operated hours)
(std) Multi-counter (injection, lot, repeating lot, warning bell, initial rejection, continuous failures, and operation)
(std) Monitoring function (up to 32 items selectable; including positions, speeds, pressures, times, and revolutions)
(std) Alarm function (cycle, up-down tolerance, heater disconnection, thermocouple disconnection, safety door, etc)
(std) Machine condition display (operating mode, completion of clamping, and ejector retraction limit)
(std) Production control function (job completion ratio, prospective time of job completion…)
(std) Maintenance function (1-cycle graphic, alarm history, grease timing display, servo amplifier communication)
(std) Self-diagnostic function
(std) Screw cold-start prevention system (with countdown time display)
(std) Fine PID temperature control (with soft-start function)
(std) PID automatic tuning function
(std) One week automatic heater on-off calendar
Vacuum device interface
Valve gate interface
Conveyor starting interface
Automatic mould clamping device interface
Quality control system (A++)
Moulding parameter control soft
Moulding machine monitor system (T-station)
(std) Injection compression system (standard specification)
(std) Pre-gating system
Holding pressure vibration system
Indicator light in one colour (red)
Indicator light in three colours (red, yellow and green; with mode selection function)
Unscrew motor connecting circuit (with socket)
Printer output terminal with ESC/P control code compatibility
(std) 100 V plug socket for printer (1 port)
100 V plug socket (2 ports, power source by customer)
100 V plug socket (2 ports, with transformer of 5 A each)
200 V plug socket (4 ports, 2 lines of 30 A each)
200 V plug socket (4 ports, 2 lines of 30 A each, with breaker)
Various signal output (4 non-voltage normally-open contacts)
Kanji character printer
(std) Local-language display (English, Chinese, (simplified/traditional), Thai, Spanish, Korean, Hebrew)
Compatibility with various voltage sources (with transformer)
(std) Setting value history
(std) Security function



(std) = standard

(std) SRC-II metering system
SRC-III metering system
(std) SNF Control
(std) Closed-loop control of injection speed, position and pressure
(std) Programmable control of injection (2 to 7 steps)
(std) Programmable control of injection (1 to 3 steps)
(std) Holding pressure changeover via position, time and pressure
(std) Slope control of injection
(std) Suck-back control (before and after metering)
(std) No-back pressure metering in manual mode (setting possible)
(std) Injection during high-pressure clamping
(std) Injection unit swivelling mechanism (with nozzle alignment mechanism)
(std) Melt run-out detection system
(std) Automatic purging system
(std) Purge cover (with interlock)
None standard diameter screw and barrel
(std) Wear resistance screw and barrel (for diameter 40 or smaller)
Wear resistance screw and barrel (for diameter 46 or larger)
Specially designed screw (contact us)
(std) Nozzle reciprocating function
Air operated check nozzle
Long nozzle / Small diameter Long nozzle
Dual-line nozzle temperature control
(std) Small diameter nozzle (for diameter 20 or smaller)
Small diameter nozzle (for diameter 24 or larger)
Separable nozzle (for diameter 36 or smaller)
(std) Separable nozzle (for diameter 40 or larger)
(std) Hopper throat temperature control (PID)
(std) Heater SSR control
(std) Heater temperature holding control
(std) Melt remaining monitor function
(std) 5-zone heater (for diameter 28 or larger screw unit)
(std) 4-zone heater (for diameter 24 or smaller screw unit)
High temperature use heater band (over 350°C up to 500°C)
Hopper (with shutter)
Hopper swivelling devices



(std) = standard

(std) Automatic greasing device
Automatic entire grease lubricating device
Mould cooling water line
Cooling water flow gauge
(std) UBS memory (Toyo specification; 1 GB) (400 mould setups)
(std) Unloaded interface
Rubber pads
(std) Accessories (mould clamp)
(std) Chute
(std) Auxiliary step



(std) = standard